Riverstone Networks RS 8000 Manuel de l'opérateur Page 144
- Page / 158
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5-10 Riverstone Networks RS 8000/8600 Switch Router Getting Started Guide
Hitless Software Upgrade Managing Software
5.4.1 Hitless Upgrade Example
The following is a step-by-step example of performing a hitless upgrade.Note that for this example, the TFTP server
IP address is 134.141.178.5 and the upgrade image path and filename is “/tftpboot/ros12.” Furthermore, in this
example, the primary CM resides in slot CM and the backup CM resides in slot CM/1.
1.
Load the new RS operating software image onto a TFTP server that is reachable by the RS.
2.
Enter the
system image add backup-cm
command to load the new software image onto the
backup CM.
rs# system image add 134.141.178.5 /tftpboot/rod12 backup-cm
**Warning: Be sure to also add this image to the
Primary Control Module so that the same images
exist on the Control Modules. Failure to do so
may prevent hot failover from working correctly.
Downloading image '/tftpboot/ros12' from host '134.141.178.5'
download: done
Adding Image (Backup CM)
to local image ros12 (takes a while) . . .
save:
kernel: 100%
images/ssr_atm: 100%
images/ssr_cmhe: 100%
images/ssr_wan: 100%
images/ssr_atm155_sar: 100%
images/ssr_atm155_fpga_400: 100%
images/ssr_atm155_fpga_800: 100%
images/ssr_mpls_dp_tmac: 100%
images/ssr_mpls_mc_tmac: 100%
images/ssr_atm622_amac: 100%
images/ssr_atm622_sar_rcv: 100%
images/ssr_atm622_sar_xmt: 100%
images/ssr_atm622_sar_diag: 100%
images/hdrproc2: 100%
done
Image checksum validated.
%SYS-I-BOOTADDED, Image 'ros12' added.
rs#
- RS 8000/8600 1
- Switch Router 1
- Getting Started Guide 1
- COPYRIGHT NOTICES 2
- RADIACIÓN LÁSER Y CONECTORES 6
- RIVERSTONE NETWORKS, INC 9
- AGREEMENT 9
- RIVERSTONE STANDARD WARRANTY 11
- TABLE OF CONTENTS 15
- LIST OF FIGURES 19
- LIST OF TABLES 21
- 1 ABOUT THIS GUIDE 23
- 2 INTRODUCTION 25
- 2.2 SPECIFICATIONS 26
- Introduction Specifications 27
- 2.3 SOFTWARE OVERVIEW 28
- IP Routing 29
- IP Multicast Routing 29
- IPX Routing 29
- 2.3.9 Web Hosting Features 32
- 2.3.10 Management Platforms 32
- 2.4 HARDWARE OVERVIEW 33
- Switching Fabric 34
- Power supply 34
- 2.4.2 Backplane 35
- 2.4.3 Fan Module 35
- 2.4.4 Control Module 35
- Boot Flash 36
- Memory Module 36
- 100-125~5A 38
- 200-240~3A 38
- 50-60 Hz 38
- 100-125V~ 10A 39
- 200-240V~ 6A 39
- 50/60 Hz 39
- 2.4.6 DC Power Supply 40
- 10/100BASE-TXG8M-HTXA2-08 42
- 87654321 44
- 10/100BASE-TXG8M-HTXB2-16 45
- 100BASE-FXG8M-HFXA1-08 47
- 100Base-FX SFP Line Card 48
- 1000Base-SX Line Card 49
- 1000BASE-SXG8M-GSXB1-02 50
- 1000Base-LX Line Card 52
- 1000Base-LLX Line Card 54
- 1000Base-T Line Card 55
- Multi-Mode Short-Reach 58
- Single-Mode 58
- Long-Reach (70 Km) 58
- ATM Multi-Rate Line Card 63
- ATM OC-12c Line Card 64
- ATM-OC-12c-SMFG8M-A12B9-02 65
- POS OC-3 MMFG8M-PO3B1-04 66
- POS OC-3 SMFG8M-PO3B9-04 66
- POS OC-12c SMFG8M-P12B9-02 68
- G8M-PO3MM-02 69
- POS MPLS OC3 69
- G8M-P12MM-02 70
- POS MPLS OC-12c/STM-4 70
- Quad Serial - CEG8M-SECAC-04 71
- Dual HSSI 73
- G8M-HSIAC-02 73
- CMTS Line Card 75
- DOCSIS CMTSG8M-CMTSNA-6X1 76
- Multi-Rate WAN Line Card 77
- Channelized T3 Line Card 80
- CHANNELIZED T3G8M-CT3BB-02 81
- 18-695-01 82
- Figure 2-44 SRP bridge module 83
- 3 HARDWARE INSTALLATION 87
- 3.3 INSTALLING THE HARDWARE 88
- 3.2 HARDWARE SPECIFICATIONS 88
- Internal Power Supply One 94
- Internal Power Supply Two 94
- RS 8600 DC Power Supply 94
- Card Guides 96
- Circuit Board 96
- Metal Plate 96
- To remove 100
- Make sure WIC is aligned 104
- Insert the WIC through the 104
- (Base Slot) 105
- G8M-SRP-MATE 106
- Insert SFP into ports 107
- 4 INITIAL CONFIGURATION 109
- If the message “ 111
- 4.2.1 CLI Access Modes 112
- CONFIGURATION FILE 114
- 4.5 SETTING UP PASSWORDS 120
- Here is an example: 122
- 4.6 SETTING UP SNMP 123
- 4.6.2 Improving SNMP Security 124
- 4.6.3 Supported MIBs 125
- KRVWQD PH RU,3DGGU! 129
- IDFLOLW\W\SH! 129
- 4.9.1 Fail Over 131
- Software/Hardware Versions 134
- Changing Mastership 134
- Hot-Swapping 134
- 5 MANAGING SOFTWARE 135
- Reboot the RS 139
- Enter the 139
- 5.4 HITLESS SOFTWARE UPGRADE 143
- 5.4.1 Hitless Upgrade Example 144
- 5.5 UPGRADING FPGA CODE 146
- APPENDIX A TROUBLESHOOTING 149
- INFORMATION 151
- Numerics 153
Produits connexes et manuels pour Mise en réseau Riverstone Networks RS 8000
(111 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels