Riverstone Networks RS 8000 Manuel de l'opérateur Page 117
- Page / 158
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Riverstone Networks RS 8000/8600 Switch Router Getting Started Guide 4-9
Initial Configuration Setting the Basic System Information
4.4 SETTING THE BASIC SYSTEM INFORMATION
Follow the procedures in this section to set the following system information:
•
System time and date
•
System name
•
System location
•
Contact name (the person to contact regarding this router)
•
IP address for the management port on the Control Module
Note
Some of the commands in this procedure accept a string value. String values can
be up to a maximum of 255 characters in length including blank spaces. Surround
strings that contain blanks with quotation marks (for example:
“string with
internal blanks”
).
1.
Enter the
enable
command to get to Enable mode in the CLI.
2.
Enter the following commands to set the system time and date and to verify your settings.
Here is an example:
3.
Enter the
configure
command to get to Configure mode in the CLI. The following commands can
be entered only from Configure mode.
4.
Enter the following commands to set the system name, location, and contact information:
Here is an example:
system set date year
QXPEHU!
month
PR QWKQDPH!
day
GD\!
hour
KRXU!
minute
PLQXWH!
second
VHFRQG!
system show date
rs#
system set date year 2003 month march day 27 hour 11 minute 54
second 0
Time changed to: Mon Mar 27 11:54:00 2003
rs#
system show date
Current time: Mon Mar 27 11:54:04 2003
system set name
VWULQJ!
system set location
VWULQJ!
system set contact
VWULQJ!
- RS 8000/8600 1
- Switch Router 1
- Getting Started Guide 1
- COPYRIGHT NOTICES 2
- RADIACIÓN LÁSER Y CONECTORES 6
- RIVERSTONE NETWORKS, INC 9
- AGREEMENT 9
- RIVERSTONE STANDARD WARRANTY 11
- TABLE OF CONTENTS 15
- LIST OF FIGURES 19
- LIST OF TABLES 21
- 1 ABOUT THIS GUIDE 23
- 2 INTRODUCTION 25
- 2.2 SPECIFICATIONS 26
- Introduction Specifications 27
- 2.3 SOFTWARE OVERVIEW 28
- IP Routing 29
- IP Multicast Routing 29
- IPX Routing 29
- 2.3.9 Web Hosting Features 32
- 2.3.10 Management Platforms 32
- 2.4 HARDWARE OVERVIEW 33
- Switching Fabric 34
- Power supply 34
- 2.4.2 Backplane 35
- 2.4.3 Fan Module 35
- 2.4.4 Control Module 35
- Boot Flash 36
- Memory Module 36
- 100-125~5A 38
- 200-240~3A 38
- 50-60 Hz 38
- 100-125V~ 10A 39
- 200-240V~ 6A 39
- 50/60 Hz 39
- 2.4.6 DC Power Supply 40
- 10/100BASE-TXG8M-HTXA2-08 42
- 87654321 44
- 10/100BASE-TXG8M-HTXB2-16 45
- 100BASE-FXG8M-HFXA1-08 47
- 100Base-FX SFP Line Card 48
- 1000Base-SX Line Card 49
- 1000BASE-SXG8M-GSXB1-02 50
- 1000Base-LX Line Card 52
- 1000Base-LLX Line Card 54
- 1000Base-T Line Card 55
- Multi-Mode Short-Reach 58
- Single-Mode 58
- Long-Reach (70 Km) 58
- ATM Multi-Rate Line Card 63
- ATM OC-12c Line Card 64
- ATM-OC-12c-SMFG8M-A12B9-02 65
- POS OC-3 MMFG8M-PO3B1-04 66
- POS OC-3 SMFG8M-PO3B9-04 66
- POS OC-12c SMFG8M-P12B9-02 68
- G8M-PO3MM-02 69
- POS MPLS OC3 69
- G8M-P12MM-02 70
- POS MPLS OC-12c/STM-4 70
- Quad Serial - CEG8M-SECAC-04 71
- Dual HSSI 73
- G8M-HSIAC-02 73
- CMTS Line Card 75
- DOCSIS CMTSG8M-CMTSNA-6X1 76
- Multi-Rate WAN Line Card 77
- Channelized T3 Line Card 80
- CHANNELIZED T3G8M-CT3BB-02 81
- 18-695-01 82
- Figure 2-44 SRP bridge module 83
- 3 HARDWARE INSTALLATION 87
- 3.3 INSTALLING THE HARDWARE 88
- 3.2 HARDWARE SPECIFICATIONS 88
- Internal Power Supply One 94
- Internal Power Supply Two 94
- RS 8600 DC Power Supply 94
- Card Guides 96
- Circuit Board 96
- Metal Plate 96
- To remove 100
- Make sure WIC is aligned 104
- Insert the WIC through the 104
- (Base Slot) 105
- G8M-SRP-MATE 106
- Insert SFP into ports 107
- 4 INITIAL CONFIGURATION 109
- If the message “ 111
- 4.2.1 CLI Access Modes 112
- CONFIGURATION FILE 114
- 4.5 SETTING UP PASSWORDS 120
- Here is an example: 122
- 4.6 SETTING UP SNMP 123
- 4.6.2 Improving SNMP Security 124
- 4.6.3 Supported MIBs 125
- KRVWQD PH RU,3DGGU! 129
- IDFLOLW\W\SH! 129
- 4.9.1 Fail Over 131
- Software/Hardware Versions 134
- Changing Mastership 134
- Hot-Swapping 134
- 5 MANAGING SOFTWARE 135
- Reboot the RS 139
- Enter the 139
- 5.4 HITLESS SOFTWARE UPGRADE 143
- 5.4.1 Hitless Upgrade Example 144
- 5.5 UPGRADING FPGA CODE 146
- APPENDIX A TROUBLESHOOTING 149
- INFORMATION 151
- Numerics 153
Produits connexes et manuels pour Mise en réseau Riverstone Networks RS 8000
(111 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels